Rubber Testing Equipment

Rubber Testing Equipment

A rubber compound is judged twice: once in the mixing room, where cure behaviour and viscosity decide whether it can be processed at all, and again on the finished part, where hardness, strength, abrasion and aging decide whether it survives service. NextGen supplies instruments for both ends of that process, for raw compound, cured sheet, film and finished components, working to DIN EN ISO 868 and DIN ISO 7619 for hardness and to BS 903 for the physical property tests.

The range covers rheometers and viscometers for the mixing room, hardness and abrasion testers for routine quality control, aging ovens and environmental chambers for durability work, and tensile frames verified to ISO 7500 for strength and elongation. Machines, consumables and calibration come from one supplier, and support continues for the life of the instrument.

Read More...


What Rubber Testing Covers

Rubber is tested at two stages. Before vulcanization, rheometers and viscometers show how a compound flows, how soon it begins to cure and how it behaves as it cures. After vulcanization, hardness, tensile, abrasion, flex, rebound, aging and density tests show whether the cured part meets its specification. A cure curve, a hardness value and a tensile curve each describe a different property, so a rubber laboratory usually combines several instruments instead of relying on one number.

Most of these methods are comparative. They rank compounds, suppliers and batches under fixed conditions and do not predict service life on their own, which is why the method, the conditions and the edition of the standard are reported with each result.

Standards for Rubber Testing

Cure behavior is measured with rotorless cure meters to ASTM D5289, and ISO 6502 gives guidance on curemeter use. Mooney viscosity, stress relaxation and scorch are covered by ASTM D1646. For cured rubber, ASTM D2240 covers Shore durometer hardness and ASTM D1415 covers IRHD hardness. ASTM D412 and ISO 37 cover tensile stress-strain properties. ASTM D5963 and ISO 4649 cover abrasion on a rotating drum, ASTM D573 and ISO 188 cover heat aging in air, and ISO 4662 covers rebound resilience.

What Affects Rubber Test Results

Durometer readings change with specimen thickness, surface condition and the way the instrument is applied, and readings from different durometer types are not interchangeable. Tensile results move with extension rate, temperature, humidity, specimen geometry and conditioning. Abrasion values depend on the abrasive sheet and its condition, and rebound results are sensitive to temperature and to the design of the instrument. Sealed and unsealed rotorless cure meters may not give the same cure curve. Holding the standard, its edition and the test conditions fixed is what makes numbers from different shifts, plants and suppliers comparable.

Rubber Testing Equipment from NextGen

NextGen supplies electromechanical universal testing machines for tensile work, hardness testers from portable durometers to automatic and temperature-controlled systems, and rheology, cure and process instruments for the compound. The range continues with abrasion, flex, fatigue and crack growth, rebound and resilience, aging and environmental, density and specimen preparation equipment. Each subcategory page lists its instruments with the standards they work to. Machines are installed and calibrated on site, your operators are trained on them, and support continues for the life of the instrument.

For Laboratories

One partner to equip your complete rubber laboratory

Rubber testing rarely stops at one machine. NextGen equips the whole elastomer laboratory, from cure and process testing to hardness, abrasion, ageing and specimen preparation, and stays responsible for it after delivery.

  • Equipment, fixtures and software
  • Installation, training, calibration
  • Lifetime technical support

Build My Rubber Lab

Sub-categories

Sub-category · 8 products Electromechanical Universal Testing Machines for Rubber Testing Electromechanical universal testing machines for rubber testing measure tensile, compression, flexural, peel, tear, and component performance with precise motor-driven control. This category covers low- to high-capacity load frames for rubber, elastomers, films, foams, adhesives, and related flexible materials. Configurable grips, fixtures, software methods, and repeatable load measurement help laboratories support R&D, production QC, education, and standards-based mechanical testing. Open Sub-category · 6 products Rubber Hardness Testing Equipment - Bench Top, Portable & Automated Solutions Rubber hardness testing equipment measures Shore and IRHD hardness on cured rubber, elastomers, O-rings, hoses and shaped parts. This category covers portable and analogue durometers on test stands, automatic Shore, IRHD and VLRH systems, temperature-controlled hardness testing and combined hardness and density stations. Open Sub-category · 4 products Rubber Rheology, Cure & Process Testing Equipment Rubber rheology, cure and process testing equipment measures how compounds flow and vulcanize before parts are made. This category covers moving die and oscillating disc rheometers for cure curves, a rubber process analyzer for dynamic properties and a Mooney viscometer for viscosity, scorch and stress relaxation. Open Sub-category · 8 products Rubber Abrasion Testing Equipment Rubber abrasion testing equipment measures how much material vulcanized rubber and elastomers lose under controlled rubbing. This category covers DIN drum, Akron, NBS, rotary and linear abrasion testers, with Martindale and Wyzenbeek testers cross-listed for rubber-coated fabrics and footwear materials. Open Sub-category · 3 products Rubber Flex, Fatigue & Crack Growth Testing Equipment Rubber flex, fatigue and crack growth testing equipment shows how compounds survive repeated bending. This category covers De Mattia flex cracking testers, Ross flex testers for soles and sheet materials and a Ross tester with a low-temperature chamber for cold flex resistance. Open Sub-category · 3 products Rubber Rebound & Resilience Testing Equipment Rubber rebound and resilience testing equipment measures how much energy an elastomer returns after an impact. This category covers pendulum rebound testers in manual and automatic versions and a vertical rebound tester based on the free-falling hammer method. Open Sub-category · 4 products Rubber Aging & Environmental Testing Equipment Rubber aging and environmental testing equipment brings heat, cold, humidity and light exposure forward into the laboratory. This category covers high-temperature aging ovens, temperature and humidity chambers, a freezing tester for cold resistance and a discoloration meter for fading. Open Sub-category · 2 products Rubber Density & Physical Property Testing Equipment Rubber density and physical property testing equipment measures density and specific gravity of cured rubber, plastics and elastomers. This category covers digital densimeters and an automated hardness and density station. Open Sub-category · 2 products Rubber Specimen Preparation Equipment Rubber specimen preparation equipment cuts dumbbells and other test shapes from sheet to the dimensions the method sets. This category covers manual cutting presses with interchangeable knives for rubber tensile and mechanical test specimens. Open

Additional products

38 products
1 Testing machines Tension, compression and bond strength on elastomers 4
2 Hardness Shore and IRHD, portable, bench top and automated 5
3 Rheology, cure and process Cure curves, Mooney viscosity and process behavior 4
4 Abrasion Wear resistance on drums, wheels and abrasive media 8
5 Flex, fatigue and crack growth Repeated bending until cracks start and grow 3
6 Rebound and resilience How much energy the compound gives back 2
7 Aging and environment Heat, cold, humidity and light 4
8 Density and physical properties Density and specific gravity 1
9 Specimen preparation Cutting dumbbells and test shapes 1
10 Software Running the test and keeping the results 1
11 Other equipment Also used in this area 5

Nothing matches that filter. Show all products

FAQs

Confirm the exact edition with your customer first. NextGen's standard pages note that DIN 53516 has been replaced in the DIN catalog by DIN ISO 4649, that the 2016 edition of ISO 6502 is marked withdrawn with ISO 6502-1 as its newer version, and that DIN 53512 is marked withdrawn. The DIN abrasion tester, moving die rheometer and pendulum rebound tester are listed under these standards. Compare results within the same standard and edition, or contact our team to map a legacy callout to a current method.

Rebound resilience is the share of impact energy a rubber gives back, so it separates lively compounds from damping ones. NextGen offers a pendulum rebound resilience tester in manual and fully automatic versions with optional specimen heating up to 100 °C, and the GenRebound vertical tester, which averages the fourth to sixth impacts of a falling hammer. ISO 4662 and ASTM D1054 cover the pendulum method.

The automatic hardness system offers a fully automated laser O-ring measuring device and Barofix centering devices, which take the operator out of positioning and suit cord diameters from 0.6 to 5.0 mm. Its IRHD M method covers thin-walled O-rings and molded parts under DIN ISO 48. Heat aging then runs in the NG-AGOV-ADV aging oven, and the specimens are re-tested for hardness, tensile strength or elongation.

NextGen offers abrasion and flex testers built around footwear soles. The NBS rubber abrasion tester is used most often for soles and heels, the DIN abrasion tester reports volume loss on a rotating drum, and the Ross flex tester rates a sole by how fast a cut grows. The GenRoss-CH adds a low-temperature chamber to test the cold resistance of shoes and shoe materials.

Yes. The automatic Shore, IRHD and VLRH hardness testing system has interchangeable Shore 00/000 and VLRH measuring units for foam rubber, silicone and sponge, plus an IRHD L unit for sponge and foam rubber. A digital ball rebound tester on the GenRebound page measures resilience of foams and polyurethane, and the NG-EML Series A lists soft foams among its typical specimens.

NextGen covers rubber and elastomer testing end to end, from the raw compound through to finished parts. The main areas are:

Tell us which properties your specification covers and we'll map them to the right systems. Contact our team or request a quote.

Work back from the property you report:

From there it comes down to your standards, throughput and specimen type. If you'd like a recommendation, contact our team.

The equipment is built to the standards rubber labs work to, mainly ASTM and ISO. Common ones by test:

  • Cure: ASTM D5289 (MDR), D2084 (ODR); ISO 6502.
  • Mooney viscosity: ASTM D1646; ISO 289.
  • Tensile: ASTM D412; ISO 37.
  • Hardness: ASTM D2240 (Shore), D1415 (IRHD); ISO 48, 7619.
  • Abrasion: ASTM D5963, D1630; ISO 4649 (DIN), 4649.
  • Heat aging: ASTM D573; ISO 188.

Each product page lists the exact standards a model meets. If a customer names one you don't see, send it over and we'll confirm it.

With a curemeter. The Moving Die Rheometer (MDR) is the modern standard: it holds a sample at test temperature and records torque as the rubber cures, giving scorch time, cure rate and optimum cure. The Oscillating Disc Rheometer (ODR) measures the same cure curve with the classic oscillating-rotor method. Both tell you how a compound will vulcanize before it reaches production. To match a rheometer to your compounds, request a quote.

Mooney viscosity measures the flow resistance of an uncured compound, which predicts how it will process. It's also used to check scorch. NextGen's Mooney Viscosity Testing Machine (GenMooney) runs the test to ASTM D1646 and ISO 289, and reports viscosity and scorch in one run.

The RPA Ultra is a dynamic rheometer that goes beyond a standard curemeter. It measures cure, plus dynamic properties like storage and loss modulus across strain, frequency and temperature, so you can characterise both processing and final in-service behaviour of a compound. It's the tool of choice for R&D and advanced quality control.

Rubber hardness is measured on the Shore A scale for most elastomers, or in IRHD for softer and thin materials. NextGen supplies manual durometers and the Automatic Shore, IRHD and VLRH system, which applies the load and reads automatically to remove operator variation. Where hardness has to be reported at a set temperature, the digiChamber temperature-controlled hardness tester conditions the specimen and tests it in one place.

On a universal testing machine configured for elastomers. It pulls a dumbbell specimen to failure and records tensile strength, elongation at break and modulus to ASTM D412 and ISO 37. Rubber needs long-travel extension and the right grips, which these frames are set up for. To size a frame to your specimens, request a quote.

Several methods exist because different products wear in different ways. NextGen supplies the main ones:

If you're not sure which method your standard calls for, contact our team.

Rubber that flexes in service, such as belts, seals and soles, is tested for crack growth and fatigue. The Demattia Flex Cracking Tester measures crack initiation and growth under repeated flexing, and the GenRoss-CH Ross Flex Tester runs flex testing with an optional low-temperature chamber. Both show how a compound holds up over many cycles rather than a single pull.

Yes, and it matters because rubber stiffens and can turn brittle in the cold. The GenRoss-CH adds a low-temperature chamber for flex testing, and the Freezing Tester (GenFreeze) determines the temperature at which a compound becomes brittle. Tell us your target temperature range and we'll spec the right set-up.

Heat aging predicts how a compound's properties change over time at elevated temperature. The Aging Oven (NG-AGOV) holds specimens at a controlled temperature for a set period, after which they're re-tested for hardness, tensile or elongation to see how much they've changed. It's a standard step for durability and lifetime claims.

With the Digital Densimeter System, which measures specific gravity quickly and repeatably. Density is a simple but valuable check on compound consistency, filler loading and batch uniformity.

Rubber dumbbells are cut from sheet with a die and a press so every specimen has the same shape. The NG-T-Press cutting press cuts clean, consistent tensile specimens, which is important because a ragged edge starts a tear and skews the result. Good specimen prep is part of getting repeatable tensile numbers.

Yes. The rheometers, viscometers and universal testing machines run under software that sets up the test, records the curve live, calculates results and exports reports. Operators run to a saved method, so results are consistent between shifts and operators.

Yes. A single universal testing machine handles tensile, tear and compression; the test changes with the grips and fixtures you fit. That covers most of a rubber lab's static testing on one frame. If you're unsure which fixtures your standards need, contact our team.

Cutting dies for tensile dumbbells, abrasion wheels and sheets, rotor and die sets for rheometers, grips and fixtures for the universal frames, and spare probes for durometers. Send your model and we'll match the right supplies to it.

Yes. Installation and commissioning are done on site, followed by hands-on training on set-up, method creation, daily verification and maintenance, tailored to your systems and standards. To plan an install, contact our team.

Yes. NextGen provides calibration and verification traceable to recognised standards, plus spare parts and both remote and on-site service. Regular calibration keeps results defensible in an audit, and support continues for the life of the equipment.

Tire and rubber manufacturers, seal and gasket makers, hose and belt producers, footwear, automotive and aerospace suppliers, and compounding and research labs. Anywhere a rubber compound has to meet a cure, hardness, strength or wear specification, this equipment does the checking.

You can request a quote for any product on this page, and the request carries the item you're interested in so we can respond quickly. Prefer to talk it through first? Contact our team, and we can arrange a demonstration or a sample test on your own compound. You can also browse the full Rubber Testing Equipment range to compare options.